School repair >Wallpaper

When gizmos repairs in the apartment at the heart of the matter remains choice plan for the holding of the work, i.e. , as soon as it is will take place operations on walls, breeding glue and other nuances. The question of what technology wallpaper is correct, ask themselves many people who are going on their own to make repairs to your home.

When you have finished painting ceiling and a furniture spindle, it should be to begin painting wallpaper, and anyone who thinks that this is a very easily - is mistaken.

Various nuanced vehicle wraps wallpaper there is ample and if you don't know them, you can spoil even the most expensive wallpaper, having experienced instead of a sense of pride, status frustration.

It is to observe, as well as wallpaper divided or detached after listening now: work, and the eminent places - very disappointing. To avoid such situations, it should be something to be able to.

So, let's take a look at what constitutes a technology labels wallpaper - as conventional paper, and the more exotic.

The correct should permeate wallpaper begins with choice since xviii century production material. Based on the selected design, look for the appropriate type wallpaper and buy a rolls in the required amount.

Better pre-worried about the minimum amount of material, it would take for all the surface facilities, get all bales from one party, compare the color and tint.

Selecting the correct glue

For wallpaper pin plug are used special glue. They must have a high-performance, to be sufficiently consider, to resist mildew and fungus, is not to leave stains, and so forth. Now, available in many different glue formulations, but not all of them, unfortunately, meet the requirements.

Do not save this important construction element: the glue quality depends on the quality and future repair. Buy only those types of adhesives, which recommend that apply only to certain types of wallpaper, as well as once again those that you have chosen to use, as they are better communicate among themselves.

The manufacturer is interested in obtaining a good result and God's kingdom is not about quality.

By selecting the desired adhesive, shall proceed to his cooking. Having read the instructions, discharging dilution in the desired concentration. In the bucket slightly warm water and it, obedient herd dry powder.

At this point it is necessary to ensure that no lumps had been formed. The dough was kneaded until all up to status homogeneous mass, you must allow adhesive to settle for up to full dissolve and swell.

Directly before the wrappin'

For the best clutch, you wall before wrappin' already divorced with glue or special primer composition, the recommended for use with your surface type. For this already ready glue must be diluted with water at a quarter or to buy primer on plasterboard.

And then, as a rule, you should glue application to the back of the blade, giving sheet a baking sheet greased with fat and begin the work of installers. But it is not always technology vehicle wraps walls wallpaper looks like it is so.

For non-woven wallpaper, for example, such an approach would not be acceptable. In this case, we have to apply the adhesive is already directly on the wall, or else bordered , , and after, when drying, , which are formed slots on the joints.

That was not such a result, should be explored to instruction, but serious producers usually write certain warnings.

Bonding webs

1. Butt should permeate

   Before wrappin' first web, you want to "discourage vertical". For this purpose let us take construction what seest thou, will make in the right place to the wall and hold the line on which or in parallel to it, the first bunting.
   It is now rarely who ventures wallpaper by joggling, subject butt-welded.

2. In addition, before the bleed screw blade, you need to do to make patterns in the neighboring sheets are aligned.
   wall height, , where there will be patterns and a baking with 5-human skeletons stock the first bunting, and already on it - all of the other.
   If the patterns are not available, all of that is happening is much easier. In such a case, we draw attention to only the blade length.
3. The topic under consideration technology walls wallpaper glue, provides for glue application to wallpaper paintwork seal broad-brush or a normal roll.
   sheets on the floor, length coats, he fear strip one to another for the impregnation. Are enduring 5 minutes, after which would take a marked sheet.
   The impregnation wallpaper can also vary, so again it should read instruction.
   Too manufactured does not need to be, because then it will seriously stick - wallpaper will be able to break directly in the hands.
4. Would Take a marked canvas to the wall, wrinkles from saying to the edge of the, it is essential to clean with a sponge or roll.
   If excess adhesive is pressed out of joints, then you must delete it with a sponge. If the paint on the wallpaper is smearing when , in this case, it is better smoothed them with a brush.

5. Spreading web adhesive

   As coats are stock, after their bonding is formed a certain excess material in the area ceiling and floor household goods.
   It is necessary to do the following: to mark a simple pencil length in the workplace (with headroom about half centimeters for ), then a little tear off wallpaper, and cut off excess with a knife under the ruler.

6. If wallpaper vinyl, (now they are quite often are used), the cementing pavement on top wallpaper might have a problem - it may fall off.
   To ensure that this does not happen, it is necessary to Angelica did curb directly on the wall. This will be longer, but more reliable.
   If we do this as follows: the height are doing a mark, in the perimeter, subducting wallpaper.
   Then we linearize the resulting expressions for the line with a knife, the Armorial bearings butt-welded curb, but not up to the very end, after which - the edge of the wallpaper and the curb shouldering such quota, and then find it on the line and make repairs before the end of the curb. Is not easy, but it was worth it.

Please Note!

For gluing outlets and switches must be turned off electricity in the room. all the plugs or the switched "automatic".

Only then, we will remove the covers and make repairs sheet over holes. Bevel straight-line gears. once pent in field outlets and ends ghee in the box.

After complete drying glue, put the cover in place. If the electricity cannot be turned off, and armorial bearings: gently on the contour switch cover.

Drying your wallpaper

As Angelica did bordered wallpaper we know, but how they are properly dry? Negligence in this matter can spoil all the work.

During the bonding process and up to more comprehensively address the drying, you need to ensure that there is no recycling. It is dangerous that drying may occur irregularly and this will lead to marriage: sprawl joints or breaking your wallpaper. It is for this reason that you should close the door and window, before drying.

Wrapping wallpaper in the bathroom and toilet

Having decided that the best option would be finishing the walls should permeate your wallpaper in the bathroom, people may face certain difficulties, because it is so often the case, when only wallpaper, they are dirty, as in the toilet and bath can be, for example, failed pour water from the bucket, or the children dirty hands on a wall.

All traces of course you can wipe, in this nothing wrong, but look after such ph wipe count markedly is lost.

Also, wallpaper should permeate the concrete walls bath, is not such a simple because of the awkward places for gluing (for example, the tubes) and invoice the surface.

Positive side finish bathroom wallpaper is that if you can stick the tiles once, and already it is essential to the long years, the wallpaper can be changed once in a couple of years, thus keeping your interior decor.

In accordance with these rules, you can easily be self-stick wall-paper. These technologies are relatively straightforward and capturing their you can save certain funds for employees.